DIP SEAL PLASTICS, INC.

ROCKFORD, IL 61108

Telephone: (815) 398-3533

Cage: 29437

PARAFFIN WAXES AND HYDROCARBON WAXES, MICROCRYST

CAS: 63231-60-7

MINERAL OIL, PETROLEUM DISTILLATES, SOLVENT-DEWAXED HEAVY

CAS: 64742-65-0

RTECS: PY8038500

Fraction By Weight: 65%

OSHA PEL 5 MG/M3

ACGIH TLV: 5 MG/M3; 10 STEL

PHTHALIC ACID, BENZYL BUTYL ESTER; (BUTYL BENZYL PHTHALATE)

CAS: 85-68-7

RTECS: TH9990000

Fraction By Weight: <5%

EPA Report Quantity: 100 LBS

DOT Report Quantity: 100 LBS

FATTY ACID, SOYBEAN OIL, EPOXIDIZED; (EPOXIDIZED SOY BEAN

CAS: 8013-07-8

RTECS: LH8010000

Fraction By Weight: <5%

PARAFFIN WAX MIXTURE CONSISTING OF INGREDIENTS 5 & 6.

RTECS: 9999999ZZ

Fraction By Weight: <5%

OSHA PEL 2 MG/M3

ACGIH TLV: 2 MG/M3

PARAFFIN WAX; FULLY REFINED.

CAS: 64742-43-4

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:YES OSHA:NO
Health Hazards Acute and Chronic:ACUTE: EYE: MELTED COMPOUND CAN CAUSE
SEVERE BURNS. SKIN: MELTED COMPOUND CAN CAUSE SEVERE BURNS.
INHALATION: DUE TO LOW PRESSURE AT AMBIENT TEMPERATURES NO
SIGNIFICANT NASAL OR RESPIRATORY IRRITATION IS EXPECTED.
INGESTION: COMPARATIVELY NON-HAZARDOUS AT ROOM TEMPERATURE.
CHRONIC: NONE ESTABLISHED.
Explanation of Carcinogenicity:CAS NO.64742-65-0 IS LISTED BY THE RTECS
AS AN GROUP 1 CARCINOGEN.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:EYE: FLUSH WITH LARGE VOLUMES OF WATER FOR AT LEAST 15
MINUTES. GET MEDICAL ATTENTION. SKIN: COOL AT ONCE! IF 2ND OR 3RD
DEGREE BURNS ARE SUSPECTED, GET MEDICAL AID. INHALATION: REMOVE TO
FRESH AIR. I NGESTION: SMALL AMOUNTS ARE ESSENTIALLYHARMLESS. CALL
MD IMMEDIATELY .

Flash Point:395F/202C

Spill Release Procedures:REMOVE ALL SOURCES OF IGNITION AROUND SPILL
AREA.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:STORE IN COOL, DRY AREA.
Other Precautions:MELTED DIP SEAL WILL PRODUCE SEVERE BURNS IF GOTTEN
ON BODY.

Respiratory Protection:NONE NEEDED. WEAR NIOSH/MSHA APPROVED RESPIRATOR
APPROPRIATE FOR EXPOSURE OF CONCERN .
Ventilation:LOCAL EXHAUST PREFERRED.
Protective Gloves:IMPERVIOUS GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:NONE.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

Hazardous Decomposition Products:INCOMPLETE COMBUSTION MAY PRODUCE CO.
Conditions to Avoid Polymerization:DIPPING TEMPERATURES IN EXCESS OF
350F.

Product ID:DS260, HOT DIP STRIPPABLE COATING-TYPE 1
MSDS Date:01/01/1987
FSC:8030
NIIN:00N031552
MSDS Number: BPLKX

Waste Disposal Methods:DISPOSE OF CONTAMINATED MATERIAL IN AN APPROVED
DISPOSAL SITE, COMPLY WITH FEDERAL, STATE & LOCAL REGULATIONS
CONCERNING WASTE DISPOSAL INTO LANDFILLS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.